Short: System-X 1.07 (eSSeXX) Bulletin Board System - Full install archive
Author: [r]FoX - Support: http://www.luebeck.netsurf.de/~clasen
Uploader: house luebeck netsurf de
Type: comm/bbs
Architecture: m68k-amigaos
System-X 1.07 (eSSeXX) Install archive
--------------------------------------
This archive contains the full install version of the
SX (eSSeXX) BBS software and all other needed files to run a
full AmiExpress styled Bulletin Board System.
System-X is on the run and will be updated permanently !
==================================================================
INSTALL NOTES
To install this software, use the supported Installer.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
The installer does no versioncheck of any systemlibary`s so
plz check that up.
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Follow the instructions by the Installer. You have any time the
posibility, to abort the installation.
If you like to install by hand, refer to the guide in the SX:Doc/
directory, chapter `Installation`.
Have a look at the guide and reset your computer.
Start the System-X BBS in your selected way and be a real \X op :)
==================================================================
Developers Internal Changes
===========================
Note(s) on further developing:
------------------------------
* To check if a file exists, use the access() function, defined in stdio.h.
This funtion basically does the same as: Lock() a file, check if lock!=0,
and then UnLock() the file again.
v1.07 -> v1.08
==============
Changes, relevant for both users and delopers:
----------------------------------------------
* Added ~MN MCI-Command to display the current MessageBase number.
* JoinedBase.ANS is now displayed when a new MsgBase is joined
Changes, relevant for developers only:
--------------------------------------
* Bumped the version number
Specified changes:
------------------
Source Procedure/Function Change(s)
~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
ver.h * - bumped version
showansi.c MCIPS - added ~MN command for current basenumber
msgs.c GotoMsgArea - added showansi("joinedbase")
v1.06 -> v1.07
==============
Changes, relevant for both users and delopers:
----------------------------------------------
* SX doesn't go into an endless loop anymore if a door isn't found.
* Wordwrapping added to chat!
* MCP now shows the correct activity when chat is finished.
* Added wildcard support to name-prompt (confirmation prompt is new string
in Strings.ANS.
+ Change the Login-Wildcard procedure more direct
+ Update the Node-Screens 'About' text
+ Update the crypted Welcome message
+ SX-Config changes up to 32 Nodes now
+ SX-MCP bumped version
+ Guides updated
Changes, relevant for developers only:
--------------------------------------
* Replaced all the version numbers into a macro, defined in ver.h
* The CallerLog() routine from prim.c is now in the log.c file.
* The LoadStrings() and FreeStrings() routines are now in configs.c
* Ver.c is renamed to Sysinfo.c, because the name confused me ;-)
+ SX-Config and SX-MCP got version-Macro, too
+ SX-Config can handle 32 nodes now again
Specified changes:
------------------
Source Procedure/Function Change(s)
~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sx.c RunDoor - checks if door parameter isn't empty
- checks if specified door exists
(both these things caused endless loops)
TestDoor - replaced a bit of code
main - replaced version strings
CheckWin - replaced version string and 'About' text
Account - added wildcard support for handle/name
- comfirmation for name is now in Strings.ANS
door_xim.c WaitForXIM - added SX_MSGAREANUM command
- replaced version string
showansi.c MCIPS - replaced version string
* - removed LoadStrings() and FreeStrings()
chat&page.c PageSysOp - added some comments
Chat - rewrote the routine almost completely
- added wordwrapping
- MCP now displays correct activity after chat
prim.c CallerLog - removed this function from the source-code
log.c * - added this file to the link-list
configs.c * - added LoadStrings() and FreeStrings()
SX-Config
---------
sx-config.c * - bumped version
sxconfig_gui.c * - changed the nodeslide value up to 32
mcpprefs.c * - changed the visible nodelist slider up
to 32 and check up the whole process
The development of System-X (eSSeXX) is going on ! [r]FoX